Working-day reply within 12h 9 years exporting · 30+ countries
Home / Insights / Wearables
Wearables2026-08-147 min read

5ATM vs IP68 on Wearables: Swim-Proof or Not

Every wearable listing carries a water rating, and every returns queue holds a device that drowned inside its rating. The two numbers printed on the box, 5ATM and IP68, come from different test systems that answer different questions. This guide explains what each rating actually measures, where each one stops protecting the device, and how to phrase water claims that customers can act on.

5ATM vs IP68 on Wearables: Swim-Proof or Not

Two ratings, two different questions

ATM ratings come from static pressure. A 5ATM wearable has been tested against the pressure exerted by a 50-meter column of still, room-temperature water, with the device motionless. The number describes a pressure test, not a depth permission: a swim stroke drives the case through the water and multiplies the instantaneous load on it, which is why the rating is not an invitation to dive anywhere near 50 meters.

IP ratings come from ingress protection testing under the IEC 60529 framework, and they answer a different question: does anything get inside. The first digit covers solids, from fingers down to dust; the second covers water, from drips to jets to immersion. IPX7 means one meter of immersion for 30 minutes. IPX8 means immersion beyond that, at a depth and duration the manufacturer declares. IP68 combines dust-tight with that manufacturer-defined immersion, and here is the detail buyers miss: the actual depth and time are whatever the factory wrote on the spec sheet, commonly 1.5 meters for 30 minutes, sometimes less, occasionally more.

The consequence is easy to state and easy to forget. The two scales are not translations of each other. A 5ATM band is not automatically better in water than an IP68 band, because the tests measure different failures under different conditions. Comparing them requires reading the declared conditions, not comparing the numerals.

What each rating covers, scenario by scenario

Mapped against real usage, the overlap and the gaps become clear:

Scenario5ATMIP68Listing advice
Rain, hand washing, sweatCoveredCoveredNo claim needed; cover the basics anyway
Shower and steamTolerated, not recommendedTolerated, not recommendedHeat and steam age seals; advise removing the device
Surface pool swimmingAccepted practiceOnly if declared immersion covers itCheck the spec sheet in writing before writing copy
Snorkeling, open waterNot coveredNot coveredNeeds a grade well beyond 5ATM with a sealed case design
Hot tub, sauna, hot springsNot coveredNot coveredHeat sits outside every wearable rating
Sea water, soapy waterRinse after useRinse after useChemicals stress the gaskets; print a rinse note

The honest summary is that 5ATM has become the de facto swim grade for mainstream bands, while IP68 sits on a wide range of products whose real water behavior varies with whatever the maker declared. Neither rating promises hot water, fast-moving water or depth.

Double declarations deserve a note of their own, because many spec sheets carry both numbers on one line. Read them as two separate statements about the same housing: the pressure grade describes how the case behaves under load, the ingress grade describes what the factory measured for dust and immersion, and the declared immersion depth, not the numeral, is what decides whether swim listings are defensible. When the two figures seem to disagree, ask which test report supports each one; a factory that cannot produce the reports is telling you something.

A fitness band clamped above a water basin during a declared-rating immersion test

Why rated devices still die in water

Seals age. The gasket that passed a factory pressure test in week one has, by month six, been compressed by a strap buckle, flexed at the lug points and cleaned with alcohol wipes. The test that mattered was the one taken before six months of wear, and no rating on the box carries forward through that history.

Conditions differ from the laboratory. Warm water softens seal material and cooling pulls micro-gaps open; soap and chlorine attack the compounds; sand finds the speaker and microphone ports. Button seals and the junction where the strap meets the case are the classic entry paths, which is why a device can pass a basin test and still leak on a customer's wrist.

Two habits cause most water returns anyway. Customers charge the device while the contacts are still wet, which corrodes the pins long before the case itself leaks, and they wear the strap loose, which lets the case lift off the skin and takes the seal out of the seat it was designed for. Both are instruction problems, and both are therefore listing problems you can fix with two sentences of copy.

What to verify on samples before volume

The verification takes an afternoon and needs only a basin, a phone timer and two sample units:

  1. Get the declaration in writing. The exact depth and minutes the factory stands behind for IP68, not a generic 68 copied onto the sheet.
  2. Run a basin test at the declared rating on two units, then check for display fogging after 24 hours.
  3. Swim once with a sample. Inspect the buttons, the strap junction and any speaker behavior afterward.
  4. Inspect the back cover seating and the charging contacts for gaps or finish damage before and after the test.
  5. Ask which variants share the same seal design, so a housing change mid-cycle does not silently change the rating.
  6. Confirm the warranty position in writing. Whatever the factory excludes for water damage becomes your cost, and belongs in your expectation setting.
A spec sheet with the declared immersion depth highlighted beside two wearable samples

Writing the listing without overpromising

State the rating, then state its scope in one plain sentence. A 5ATM device supports the phrase swim-ready for surface swimming. An IP68 device whose declared immersion is 1.5 meters for 30 minutes supports splash-proof and brief immersion, and nothing beyond that. The absolute word waterproof is best left out of the copy entirely, because it is the one word customers litigate.

Two lines prevent most water returns and cost nothing: dry the charging contacts before charging, and skip the sauna and the hot shower. State what the warranty excludes in the same listing, at the same font size as the features. Buyers forgive a product that told them the truth about its limits far more reliably than one that hid them, and the returns data always reflects which approach the listing took.

Translation is the other leak. A careful English listing can arrive in another language with the scope sentence dropped, leaving only the absolute word standing in a market where it reads even stronger. If you localize, localize the scope sentence with the same priority as the feature list, because water returns do not check which language the buyer read.

Sourcing note

Water resistance is decided by case design, gasket geometry and assembly quality, which makes it a structural specification: changing a rating is OEM territory, negotiated on the OEM/ODM page where sampling runs 7-12 days. One-piece samples ordered through dropshipping are enough to run the basin test above; bands travel through the battery-ready channel in 8-18 days, so plan the test window accordingly. The current watch and band lineup with their declared ratings sits on the wearables category page.

FAQ

Can customers swim with a 5ATM band?

Surface swimming is the accepted use case for 5ATM in mainstream wearables: pool lengths, not diving, and not hot water. A rinse after the pool or the sea keeps chemicals off the seals, and the listing should say all of that rather than just the number.

Is IP68 better than 5ATM?

Neither is better, because the two tests measure different things. 5ATM is a static pressure grade, while IP68 means dust-tight plus whatever immersion depth and duration the manufacturer declared. Compare the declared conditions on the spec sheet, not the numerals on the box.

Why did a rated watch still leak in the shower?

Heat and steam age the seals, cooling opens micro-gaps, and button seals plus the strap junction are the usual entry paths. Hot water sits outside the test conditions of both rating systems, which is why showering with a wearable is tolerated by some products and advised against by most sourcing guides.

Sourcing any product mentioned here? TECHORIGIN supplies it from Shenzhen with 1-piece dropshipping, 48-hour dispatch and OEM customization. Get a quote or browse the six categories.